Alex Table Tennis - MyTableTennis.NET Homepage
  New Posts New Posts RSS Feed - Thinnest 7-ply composite blade
  FAQ FAQ  Forum Search   Events   Register Register  Login Login
tabletennis11.com

Thinnest 7-ply composite blade
 Post Reply Post Reply Page  <12
Author
  Topic Search Topic Search  Topic Options Topic Options
HowToPlayChineseLoop View Drop Down
Super Member
Super Member
Avatar

Joined: 02/06/2012
Location: 0
Status: Offline
Points: 266 		Post Options Post Options   Thanks (0) Thanks(0)   Quote HowToPlayChineseLoop Quote  Post ReplyReply Direct Link To This Post Posted: 08/16/2012 at 1:39pm
Waldner Ultra Senso Carbon, 80g, 5.0mm ?????


So what is the result ? I also want o thinnest, lightest 7layer composite blade?

Tell me the result !
Back to Top
Sponsored Links


Back to Top
bbkon View Drop Down
Premier Member
Premier Member


Joined: 04/19/2005
Location: Afghanistan
Status: Offline
Points: 7260 		Post Options Post Options   Thanks (0) Thanks(0)   Quote bbkon Quote  Post ReplyReply Direct Link To This Post Posted: 08/16/2012 at 1:45pm
Originally posted by HowToPlayChineseLoop HowToPlayChineseLoop wrote:

Waldner Ultra Senso Carbon, 80g, 5.0mm ?????


So what is the result ? I also want o thinnest, lightest 7layer composite blade?

Tell me the result !

I got a titanium 5.4 but was so flexy and low throw ,,  is there ant old clipper replacement ..solid and fast enough while 5.5mm-6mm?
Back to Top
debraj View Drop Down
Premier Member
Premier Member
Avatar

Joined: 06/04/2007
Location: United States
Status: Offline
Points: 3369 		Post Options Post Options   Thanks (0) Thanks(0)   Quote debraj Quote  Post ReplyReply Direct Link To This Post Posted: 08/16/2012 at 1:59pm
Originally posted by slevin slevin wrote:

Originally posted by debraj debraj wrote:

Originally posted by slevin slevin wrote:

Originally posted by debraj debraj wrote:

however as you go for thinner blades...if you use hard sponged rubber, opening loops may suffer. 

Interesting. Why does this happen - flex bad for close to the table when paired with hard sponge?

what happens is to use the sponge the ball needs to penetrate it.... deform it. 

So you need good compression between the blade and the rubber. Now the flex blades exhert that pressure only after it has flexed much.... the pressure increases proportionally with the amount of deformation (shear strain). So only when you go for a full bodies shot then the rubber will get properly squeezed to produce a predictable lift. 

in short opening strokes that much of pressure(perpendicular component) is not generated. hence there is tendency of ball slippage ...going to net. 

makes any sense?Confused

I see your point, thanks. I must add that it (difficulty in opening loops while using a thin blade & hard sponge) also depends on the type of equipment - I used R7 (sort of a hard sponge) and its high-ish throw helped in the opening loops (during which thin blades flex less).


you are right. however i was considering sponges that are harder than Rakza 7 like hexer HD or Aurus.
729-F1||Rhyzm-P(FH)|| Rasant Grip orRhyzm-P max(BH)
vid1
Vid 2
Back to Top
Pondus View Drop Down
Gold Member
Gold Member
Avatar

Joined: 04/07/2012
Location: United States
Status: Offline
Points: 1933 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Pondus Quote  Post ReplyReply Direct Link To This Post Posted: 08/16/2012 at 2:02pm
As stated several times ealier, Nexy Calix is somewhere between 4.7mm and 4.9mm... I'm not sure why any of you continue to list blades that over 5mm... unless you don't bother to actually read the thread. Ermm 
Back to Top
redbee View Drop Down
Member
Member


Joined: 08/15/2012
Status: Offline
Points: 10 		Post Options Post Options   Thanks (0) Thanks(0)   Quote redbee Quote  Post ReplyReply Direct Link To This Post Posted: 08/17/2012 at 1:54am
Originally posted by HowToPlayChineseLoop HowToPlayChineseLoop wrote:

Waldner Ultra Senso Carbon, 80g, 5.0mm ?????


So what is the result ? I also want o thinnest, lightest 7layer composite blade?

Tell me the result !


tried that WUSC before but the shape doesn't fit well. Currently using T5000 and may try Calix or V1, still thinking at the moment...


Edited by redbee - 08/17/2012 at 1:55am
Back to Top
 Post Reply Post Reply Page  <12
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.01
Copyright ©2001-2018 Web Wiz Ltd.

This page was generated in 0.438 seconds.

Become a Fan on Facebook Follow us on Twitter Web Wiz News
Forum Home | Go to the Forums | Forum Help | Disclaimer

MyTableTennis.NET is the trading name of Alex Table Tennis Ltd.

Copyright ©2003-2024 Alex Table Tennis Ltd. All rights reserved.