|
|
LF: Used Rubbers (JPEN) |
Post Reply |
Author | |
redferrari
Super Member Joined: 09/14/2009 Location: Malaysia Status: Offline Points: 318 |
Post Options
Thanks(0)
Posted: 10/03/2009 at 10:10pm |
I am on the lookout for some used (but very good condition) rubbers suited for a square JPEN. Anyway has T05 or T64 or any other rubber with the equivalent specs and performance?
Let me know: 1. Wht brand and model? 2. Age and condition 3. Cut size, especially the base/bottom/length and height 4. Asking $ Thanks |
|
Sponsored Links | |
redferrari
Super Member Joined: 09/14/2009 Location: Malaysia Status: Offline Points: 318 |
Post Options
Thanks(0)
|
Thanks wyatt, got your PM. I have previously contacted this person. This particular person has been advertising for quite a while but has been very fickle minded. The last he told me he decided not to sell!!
|
|
joris
Gold Member Joined: 05/15/2007 Location: United States Status: Offline Points: 1301 |
Post Options
Thanks(0)
|
I have some used short pips of jpen, you pay shipping only.pm if interest.< id="gwProxy" ="">< ="jsCall();" id="jsProxy" ="">
|
|
joris
|
|
redferrari
Super Member Joined: 09/14/2009 Location: Malaysia Status: Offline Points: 318 |
Post Options
Thanks(0)
|
joris...... u got mail.
|
|
Pandakuo777
Member Joined: 10/03/2009 Status: Offline Points: 18 |
Post Options
Thanks(0)
|
I have 3 tenergies that i'im trying to get rid of, they were on my TImo BOll ALC so they will fit your paddle. There is a black and red 1.9mm and 2.1mm red. All were used for less than 2 hours. I'm not asking for much honestly, I would seriously consider $20 a piece. I am actually looking for 2 sheets of brand new Sriver or Sriver EL 1.9 which is valued at about 60$ brand new anyway. So if won't mind a trade or to sell. Personally, i don't need all the spin and speed that tenergy offers and need MORE CONTROL. If your interested just let me know. The 1,9mm's went through 2 glueings with free chack but are still is 8/10 shape, the 2.1mm red is definately like 9/10 cause I just got it tonight and was upset when it didn't work for me. I rather just get rid of all three at once.
|
|
redferrari
Super Member Joined: 09/14/2009 Location: Malaysia Status: Offline Points: 318 |
Post Options
Thanks(0)
|
Can they fit the JPEN without any compromise at the bottom end of the rubber that you have cut for the TB-ALC, where I do not need to sacrifice and cut the actual wordings at the bottom end of the rubber to fit a JPEN? I am keen, let me know. Thanks
|
|
redferrari
Super Member Joined: 09/14/2009 Location: Malaysia Status: Offline Points: 318 |
Post Options
Thanks(0)
|
PM me, Pandakuo777, I have new uncut Srivers. But would first need to make sure the T05s can fit nicely into JPEN without any compromise. Perhaps you can PM me the base/bottom measurements (in mm please). Thanks
|
|
Jonan
Premier Member Joined: 02/18/2009 Location: Elsweyr Status: Offline Points: 2933 |
Post Options
Thanks(0)
|
I just compared rubber off of my blades (Because I have a LOT of spare rubber sitting around I was just organizing trying to mix and match onto blades) to my J-Pen a Yasaka Musashi, and there would only be a gap of around 1/2" if you choked it up to it, and my J-Pen is pretty small in the head. J-Pen are just short of C-Pen in hardness to get rubbers to fit on, I've had some ugly looking penholds. I have another Yasaka, my first blade, and it has that black lip near the handle on the top, and putting a shakehand rubber on it, it went over the place thats' there for your fingers a good 3/5" to where I have my fingers on the rubber itself a little, and it still doesn't quite round off onto the corners. |
|
redferrari
Super Member Joined: 09/14/2009 Location: Malaysia Status: Offline Points: 318 |
Post Options
Thanks(0)
|
Jonan, can you pm me the rubbers you have. Let me know how much life they have and what are their measurements (vertical and horizontal, in mm please). Can you also email me the pics? I'll pm you my email. Thanks
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Forum Home | Go to the Forums | Forum Help | Disclaimer
MyTableTennis.NET is the trading name of Alex Table Tennis Ltd. |