tenergy problem
Printed From: Alex Table Tennis - MyTableTennis.NET
Category: Equipment
Forum Name: Equipment
Forum Description: Share your experience and discussions about table tennis equipments.
Moderator: haggisv
Assistant Moderators: position available
URL: http://mytabletennis.net/forum/forum_posts.asp?TID=20266
Printed Date: 04/27/2024 at 4:20am
Software Version: Web Wiz Forums 12.01 - http://www.webwizforums.com
Topic: tenergy problem
Posted By: F.Z.
Subject: tenergy problem
Date Posted: 08/20/2008 at 4:49pm
|
i play with my tenergy for 2 weeks now, about 40 hours, and now the upper layer comes of of the sponge. does somebody have that problems to,and what to do?
------------- BTY Timo Boll Spirit ST FH: tenergy 05 2.1(B) BH: tenergy 64 2.1 (R) |
Replies:
Posted By: Master_of_loops
Date Posted: 08/20/2008 at 4:52pm
|
You can stick it to the sponge by BTY Free chack ------------- 
|
Posted By: F.Z.
Date Posted: 08/20/2008 at 4:54pm
the problem by doing that is that it is in the centre of the rubber ------------- BTY Timo Boll Spirit ST FH: tenergy 05 2.1(B) BH: tenergy 64 2.1 (R) |
Master_of_loops wrote:Posted By: DeathAngel
Date Posted: 08/20/2008 at 4:54pm
|
Ive been using Tenergy for around 2-3 months now and i have not had a problem yet! Just use a tooth pick and apply a small bit of glue into the spot and than get 2 books or a press and press it together so it is smooth. ------------- Korbel ST H3 Neo 2.2 Desto F3 2.0 USA: 1522 CAN: 809 |
Posted By: Master_of_loops
Date Posted: 08/20/2008 at 4:57pm
Good solution. I will remember it, because maybe this can happen to me, because I use the Tenergy 05 -------------
|
Posted By: dalamchops
Date Posted: 08/20/2008 at 6:20pm
|
4 months and no problem. Not as crisp as it was brand new, but still plenty power
------------- Stiga Titanium 5.4 Cpen Andro Hexer Pips 2.1 Donic Acuda S2 Max |
Posted By: Brainstorm69
Date Posted: 08/20/2008 at 11:59pm
|
Can you return it to the seller for an exchange? Sounds like it might defective. ------------- F3S | Tulpe T-7007 | F3S |
Posted By: Mithrra
Date Posted: 08/21/2008 at 1:31am
|
YAYA... poor quality ... have been using since its launch.... and have been removing and regluing.... no problem
------------- Member of the Single Ply Hinoki Club *Non-Stop Changing Equipments!!!* HADO ST ASUKA 1 ply hinoki Accoustic FL AVX J-Power KKT Cho Tokusen-Tenergy05 |
Posted By: DeathAngel
Date Posted: 08/21/2008 at 1:48am
|
Does your shrink at leat 2-4 mm after you reglue for the first time?
------------- Korbel ST H3 Neo 2.2 Desto F3 2.0 USA: 1522 CAN: 809 |
Posted By: Master_of_loops
Date Posted: 08/21/2008 at 12:58pm
So if I want to move it from my Maze to Mizutani, Tenergy will shrink? -------------
|
Posted By: DeathAngel
Date Posted: 08/21/2008 at 2:30pm
|
I think it might... because i cut my big on a Korbel and than tried to stick it to my Stigo OC and it was to small so i had to put it a bit higher. And i tried my Sriver-EL and it fit fine. Maybe its just my wierd climate that effects the sriver because its always raining and than sunny and stuff.
------------- Korbel ST H3 Neo 2.2 Desto F3 2.0 USA: 1522 CAN: 809 |
Posted By: Master_of_loops
Date Posted: 08/21/2008 at 7:46pm
 So, you recommend me to cut Tenergy little biger then is mine Maze OFF blade head? -------------
|